Description
Task summary: Create a 10-slide powerpoint over the attached document. Speaker notes are not needed, but every slide should have at least 1 picture and 100 words on it. Use other 2-3 sources besides the attached doc. I will add 12 more hours to the DDL once the order is picked up.
Full order description:Dear Freelancer,please create a presentation based on the text document provided
MAIN DETAILS:
topic is How to do a Full System Restore for RP5800/RP5810/FlexPro Computers
Required: Instrument Full Installation Image Disk(s) OR The Full Backup Restore Tool (FBRT) – USB drive
ATTACHED:
– details
Unformatted Attachment Preview
How to do a Full System Restore for RP5800/RP5810/FlexPro Computers
** Required **
Instrument Full Installation Image Disk(s) OR
The Full Backup Restore Tool (FBRT) – USB drive
Warning: Full System Restore will replace everything on the computer, including
any changes to users, passwords, configuration, new isolates, BCI/BCILINK,
printers, and modems/Vilink configurations since the last full system backup was
created.
*** The restore program will NOT launch off the last Full System Backup disk. It is required to have the
RP5800 Full Installation DVD (or Full System Backup/Restore Tool on a USB). The Instrument PC Full
Installation DVD does not matter if it is for Observa, Vitek, etc.; it will work on either RP5800/RP5810
computers *** (Just for booting ghost application)
Using the DVD Full Installation Image Disk(s) to Restore
1) Close or exit the System Software.
2) Put the Instrument Systems Full Installation DVD – Disk 1 into the CD/DVD drive. Typically, there
are two disks. Always use Disk One. If the DVD drive opens and kicks the disk out, just reinsert Disk
one. Do not put Disk Two into the CD/DVD drive as this will give you an error of “No backup on
optical drive.”
3) Select Start > Shutdown > Restart > OK.
4) Wait 1-2 minutes for the program to load. You will see a DOS box that runs executable files. The
top bar will say X:windowssystem32cmd.exe-startnet.cmd
If this does not load or goes back to loading Windows, then follow the instructions for Changing the
Boot Sequence on page 15.
When you see this screen, then Click on US under Keyboard Layout.
5) Select Restore and Click NEXT.
6) Select DVD and Click NEXT.
2
7) A Message will appear to: “Remove the DVD Boot Media and insert a restore DVD if needed”.
Insert the Full System Backup Disk; Disk 1 if there are multiple disks. Wait until the drive light stops
blinking. Click OK.
9) Click on the drive name (Ghost_001(E) in the following image) and Click NEXT.
3
10) Select Restore.
11) A warning message will come up advising all data will be erased. Click OK.
12) The Ghost program will initiate and the progress bar near the top of the screen will start.
4
5
13) If multiple DVDs are required, the restore will stop and request the next DVD.
Insert the next DVD and select OK.
14) After the restore completes, a message appears if the restore has been successful. If the restore
was successful, select EXIT.
If the restore failed, select RESTART. Go through the process again.
6
7
15) A message will appear to “Remove the initial boot media and click OK to restart.” Remove the
DVD. Click OK to reboot the system. After the computer reboots, log in and confirm that the
Insturment software launches.
♦♦ At this point, this is considered a clean install. If the customer is starting fresh due to
some data corruption or other data-related errors or issues, the system is ready for use. ♦♦
OR
♦♦ A data backup can be restored to bring the system up to current as close as possible or at
least up to the point where data corruption occurred.
8
Using the Full Backup Restore Tool (FBRT) to Restore RP5800/RP5810
1) Close or exit the Instrument Software.
2) Insert the USB FBRT into one of the computer’s USB drives.
3) Select Start > Shutdown > Restart
If this does not load or goes back to loading Windows, then follow the instructions for Changing the
Boot Sequence on page 15.
4) Select US keyboard
5) Click RESTORE, then Click NEXT.
9
6) Select USB, or if using a DVD image disc, select DVD. Click NEXT.
7) Select the location that contains the image to restore from.
10
11
8) Click on the drive name (Ghost_001(E) in the following image) and Click NEXT.
9) Select RESTORE.
10) A warning message will come up advising all data will be erased. Click OK.
12
11) The Ghost program will initiate and the progress bar near the top of the screen will start.
12) If multiple DVD’s are required, the restore will stop and request the next DVD.
Insert the next DVD and select OK.
13) After the restore completes, a message appears if the restore has been successful. If the restore
was successful, select EXIT.
13
If the restore failed, select RESTART. Go through the process again.
15) A message will appear to “Remove the initial boot media and click OK to restart.” Remove the
DVD. Click OK to reboot system. After the computer reboots, log in and confirm that the Observa
software launches.
14
At this point, this is considered a clean install. If the customer is starting fresh due to some data
corruption or other data related errors or issues, the system is ready for use.
OR
A data backup can be restored to bring the system up to current as close as possible or at least up to
the point where data corruption occurred.
Changing the Boot Sequence
*** If the restart brings up Windows desktop, the Boot Sequence will need to be changed so it
reads the Ghost program from the CD or the USB FBRT.
Select Start > Shutdown > Restart
As soon as the screen goes black and the computer starts to reboot, press the F9 or ESC key until
the Boot Device option window displays.
If prompted for a BIOS password please insert b1oMerieux (Internal Use Only)
15
16
Use the ↑ and ↓ to get to the USB drive (usually the KingstonDataTraveler/Transcend) or the
CD/DVD drive that
the Full System Backup CD is in. Select ENTER.
The system will boot from the USB FBRT or from the CD System Backup Disk
Using the Full Backup Restore Tool (FBRT) to Restore FlexPro
1) Close or exit the Instrument Software.
2) Insert the USB FBRT & Bit Locker Key (If available) into one of the computer’s USB drives.
3) Select Start > Shutdown > Restart
If this does not load or goes back to loading Windows, then follow the instructions for Changing the
Boot Sequence on page 14.
4) If prompted for encryption verify Bit Locker Key (USB) is inserted and press enter.
5) Select US keyboard
17
6) Select the Disk icon on the top right. (Do not select the ghost icon).
7) Select the restore tab.
8) Proceed as shown in the previous section
(Using the Full Backup Restore Tool (FBRT) to Restore RP5800/RP5810
18
19
20
Purchase answer to see full
attachment
